SOREX WIFI UniLock Wall Reader
1. Package Contents
The package contains:
- Unilock indoor unit incl. cable for connection with outdoor unit
- Unilock outdoor unit incl. cable for connection with indoor unit
- Pluggable screw terminal for indoor unit for connection with electric door opener and power supply
2. Technical Data
Article number |
DO501000 |
EAN |
0685717261229 |
Special feature |
External relay cable (indoor unit) for sabotage protection |
Encryption of indoor and outdoor unit |
AES 128 bit |
Frequency |
2,4 GHz |
IP protection class |
IP66 (if glued on waterproof) |
Temperature range |
-30 to 60°C |
Power supply |
12/24V DC, min 0.5A |
Relay |
1A/250V Switching current/switching voltage |
Compatibility |
With all current motor locks (KFV, ROTO, GU, Fuhr, Wilka, Dom, ...) |
Storage of access media |
Permanent (even after power outage) |
Number of media |
100 fingerprints 150 numeric codes 200 RFID media Unlimited eKeys |
3. Milling Drawing
in mm (not to scale)
Total depth: 20mm
Installation depth: 15mm
4. Mounting / Wiring
4.1 Mounting surface box (optionally available)
4.1.1 Scope of delivery
The scope of delivery includes:
- Front panel with recess for the SOREX Unilock WiFi
- Black rear panel with recess
- Sealing frame (white)
- Cable seal (white)
4.1.2 Monnting
- Step: Put the relais cable of the SOREX Unilock WiFi into the wall.
- Step: Place the cable seal on the recess of the rear panel. To do this, a hole for the cable must be cut out of the cable seal. After putting the cable through the hole it should afterwards be sealed with acrylic.
- Step: Span the sealing frame on the rear panel.
- Step: Thread the cable from the SOREX Unilock WiFi through the recess of the front panel and then through the cutout of the cable seal into the wall.
- Step: Connect the relais cable and the cable coming from the outdoor unit. Now test the device and wiring again, before completing the mounting.
- Step: Attach the rear panel to the wall with the four fitting screws. We recommend sealing the screw holes with acrylic.
- Step: Place the front panel on the rear panel.
- Step: Glue the Unilock WiFi with the double sided adhesive tape on the front panel.
- Step: In addition, you can seal the SOREX Unilock WiFi with a silicone joint around the glass plate.
4.2 Mounting flush-mounted box (optionally available)
Brickwork - Installation
Hollow wall - Installation
4.3 Mounting without surface box or flush-mounted box
- First, mill the hole in the mounting area of the wall or door leaf.
- Then, thread the cable through the milled hole. Afterwards, you can connect the cable of the outdoor unit with that of the indoor unit. Make sure that the indoor unit is not accessible from the outside (e.g. by pulling out the cables).
4.4 Wiring Relay (Indoor Unit) with Door Opener
ATTENTION: Make sure to carry out an electrical test and confirm that the unit is in working order. Check that the Unilock is powered and perform a test opening. Check whether the door opener releases.
Note: If the unit is in the factory setting, you can enter the code "123456" on the keypad and confirm by pressing the "tick" in order to perform a test opening.
4.5 Finishing the installation
- Provided the previous tests were successful, you can now finish the installation. To do so, peel off the protective film of the double-sided adhesive tape on the Unilock and stick it to its desired mounting location.
- After gluing the Unilock in place, be sure to check that it is waterproof.
You can test this by carefully running water over the unit. Then check whether there is water behind the device. If this is the case, firmly press the unit against the mounting area again and give the adhesive glue some more time before carrying out another water test.
If water is still behind the device after another water test, you can additionally apply silicone around the glass plate.
5. Smartphone App
Search for the SOREX SmartLock app in the Google Play Store or Apple Store and install it.
You can find instructions for the SOREX SmartLock app here.
6. Reset
You can reset the SOREX Unilock WiFi in the following two ways:
- Delete the Unilock from the app (select door handle -> Settings -> "Delete"). You have to be within range of the unit to do so.
or
- Press the reset button on the indoor unit for approx. 3 seconds or until two signal tones are played in quick succession.
Comments
0 comments
Please sign in to leave a comment.